Finally, it has become hit and Nigam come to the music industry by this song. • “Kismat ” is his first album that was released from the music banner Magna Sounds. Sonu nigam sad songs download free mp3. And then finally director recruit Nigam for singing it and open Sonu Nigam video songs publicly.
. Ceiling FanInstallation InstructionsModel #: AC-19242Please Read and Save. 1. TOOLS AND MATERIALSREQUIREDPhilips screw driverBlade screw driver11 mm wrenchStep ladderWire cutters2. PACKAGE CONTENTSbUnpack your fan and check the contents. Youshould have the following items;ca.b.c.d.e.f.g.h.i.j.k.l. SAFETY RULES8.
![]() ![]() ![]()
Avoid placing objects in the path of theblades.1. To reduce the risk of electric shock, insureelectricity has been turned off at the circuitbreaker or fuse box before beginning.9. To avoid personal injury or damage to thefan and other items, be cautious whenworking around or cleaning the fan.2. All wiring must be in accordance with theNational Electrical Code and localelectrical codes.Electrical installationshould be performed by a qualifiedlicensed electrician.10. MOUNTING OPTIONSIf there isn't an existing CUL listed mountingbox, then read the following instructions.Disconnect the power by removing fuses orturning off circuit breakers.Outlet boxSecure the outlet box directly to the buildingstructure. Use appropriate fasteners andbuilding materials. The outlet box and itssupport must be able to fully support themoving weight of the fan (at least 50 lbs).
Donot use plastic outlet boxes. HANGING THE FANCeiling hangerbracketREMEMBER to turn off the power.
Follow thesteps below to hang your fan properly:Ceiling canopyStep 1. Remove the decorative canopy bottomcover from the canopy by turning the covercounter clockwise. 5)Canopy coverFigure 5Step 2. Remove the hanger bracket from thecanopy by removing the non-slotted screwsfrom the bottom of the mounting bracket andloosening the slotted screw a half turn from thescrew head. MAKE THE ELECTRICCONNECTIONSCode switchWARNING: To avoid possible electricalshock, be sure electricity is turned off at themain fuse box before wiring.ONNOTE: This remote control unit is equippedwith 16 code combinations to prevent possibleinterference from or to other remote units.The frequency switches on your receiver andtransmitter have been preset at the factory.
Note: Fan must be installed at a maximumdistance of 20 feet from the transmitting unitfor proper signal transmission between thetransmitting unit and the fan's receiving unit.7. INSTALLATION OFSAFETY SUPPORTAn additional safety support is provided toprevent the fan from falling. Secure the safetycable to the ceiling joist with screw andwasher, as illustrated in Figure 12.Hanger bracketSafety cableFigure 128.
Download free software easy activator v.0.57.213. Microsoft office 2010 toolkit activator Full Download Office 2010 Toolkit is the universal and unique activator to make active your Microsoft office for the lifetime.
FINISHING THEINSTALLATIONStep 1. ATTACHING THE FANBLADESStep 1. Insert the blade through the slot on themotor housing. Align holes and fasten theblade to the blade bracket with screws andfiber washers provided. Repeat this procedure for remainingblades.CAUTION: Maketightened securely.sureallscrewsareSlotsBladeScrewsFiber washersFigure 1410. INSTALLATING THEMOUNTING PLATEStep 1.
Remove the 1 of 3 screws from themounting ring and loosen the other 2 screws.(Do not remove)Step 2. ATTACHING THELIGHT PLATENOTE: Before starting installation, disconnectthe power by turning off the circuit breaker orremoving the fuse at fuse box. Turning poweroff using the fan switch is not sufficient toprevent electric shock.403B-1Raise and hold the light plate close to themounting plate and proceed to do the wireconnections, follow the same procedure withthe black wire connectors. INSTALLING THETRANSMITTERHOLDEROutlet boxSwitchWall plateSelect a location to install your remote controlsystem transmitter.
You can replace anexisting wall switch or, install the transmitteron ANY flat surface.Option 1: Install the cremote ontrol systemusing an existing wall switch outlet box. Makesure the electrical power is TURNED OFF atthe main panel before continuing.Figure 18Step 1. Remove the existing wall plate and theold switch from the wall outlet box. INSTALLING THEBATTERYRemove the back cover on the transmitter andinstall both, 3 volt (#2032) batteries that wereincluded with the remote control. Make surethe + sign is facing up.
OPERATING YOURTRANSMITTERFigure 21Restore power to ceiling fan and test forproper operation.A.,andbuttons:These three buttons are used to set thefan speed as follows:= low speed= medium speed= high speedB.button:This button turns the fan off.C. CARE OF YOUR FANHere are some suggestions to help maintain your fan.1. Because of the fan's natural movement some connections may become loose.
Check thesupport connections, brackets and blade attachments twice a year. Make sure they are secure.(It is not necessary to remove fan from the ceiling).2. Clean your fan periodically to help maintain its new appearance over the years. Use only a softbrush or lint free cloth to avoid scratching the finish. TROUBLESHOOTINGProblemSolutionFan will not start.1. Check circuit fuses or breakers.2.
Designer Ceiling Fans With Lights
Check line wire connections to the fan and switch wire connections in theswitch housing. CAUTION: Make sure main power is off.3. Check to make sure the dip switches from the transmitter and receiver areset to the same frequency.Fan sounds noisy.1. Make sure all motor housing screws are snug.2.
Make sure the screws that attach the fan blade bracket to the motor hub istight.3.
Clicking on the ceiling fan remote repeatedly is not the proper way to troubleshoot an operations problem. Fans that shut off or change speeds randomly likely have a settings issue. The fan's dip switch settings must be arranged in the correct order to receive and transmit the functions you select with the remote control. Placing more than one fan in close proximity also affects the fan's performance. Enjoy the cooling effects of your ceiling fan without pulling the cord continuously.
A few adjustments to a dip switch could make difference.
Designer Ceiling Fans Without Lights
Thanks for watching! Enjoy 5% OFF your order with the exclusive coupon code DMYT5 Using our Westinghouse Hayden ceiling fan Del Mar Fans and Lighting shows you how to change the frequency on your ceiling fan's remote control. Here's a list of steps to follow.
Make sure to turn the power off of your ceiling fan at the circuit breaker. Detach your canopy from the mounting bracket by removing all screws. Retrieve the receiver from the mounting bracket and locate the dip switch settings.
The dip switch settings look like four sliding buttons. Using a ballpoint pen/small screwdriver to slide the buttons to create a new frequency combination. Tutorial belajar bahasa arab pdf. Place the receiver back into your mounting bracket and attach the canopy to the mounting bracket. Remove the back of your remote control and remove the battery. Locate and remove the small panel covering your dip switches. Use a ballpoint pen/small screwdriver to slide the buttons to match your receiver's frequency. Place back panel and remote back.
Restore power to your ceiling fan. Verity settings are correct by turning ceiling fan on/off. Del Mar Fans and Lighting is an online ceiling fan and light fixture distributor with 19 years of industry experience. We strive to provide quality products, outstanding customer service, unbeatable prices, and in-depth product knowledge.
Visit us at Connect with us through our other social media channels for news, sales and giveaways. Facebook: Google+: Twitter: Pinterest: Education Center.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |